ARB 6821201 Fog Light Kit For Deluxe ARB Bumpers

ARB 6821201 Fog Light Kit For Deluxe ARB Bumpers

ARB 6821201 Fog Light Kit For Deluxe ARB Bumpers

ARB 6821201 Fog Light Kit For Deluxe ARB Bumpers

  • Optional Fog Light Kit For Toyota 200 Series 2007-09

Fog Light Kit.

List Price: $ 91.24

Price: $ 87.40

Similar Posts
Set of 4 | 1.5″ 5×5.5 (5×139.7) Wheel Spacers | Fits Dodge Ram 1500 Ford F-100 Bronco Jeep CJ | 1/2″ Studs
Set of 4 | 1.5″ 5×5.5 (5×139.7) Wheel Spacers | Fits Dodge Ram 1500 Ford F-100 Bronco Jeep CJ | 1/2″ Studs
Set of 4 | 1.5″ 5×5.5 (5×139.7) Wheel Spacers | Fits Dodge Ram 1500 Ford F-100 Bronco Jeep CJ |...
Mac Auto Parts 36937 Toyota Pick Up 4 Runner T1 Rear Axle Wheel Bearing
Mac Auto Parts 36937 Toyota Pick Up 4 Runner T1 Rear Axle Wheel Bearing
Mac Auto Parts 36937 Toyota Pick Up 4 Runner T1 Rear Axle Wheel Bearing this item i a PTC BRAND...
Self-Healing Clear Paint Protection Bra—Door Sill Kit (64in x 3in)
Self-Healing Clear Paint Protection Bra—Door Sill Kit (64in x 3in)
Self-Healing Clear Paint Protection Bra—Door Sill Kit (64in x 3in) We Only Offer High Quality Self-Healing Paint Protection Bra Helps...

3 Comments

  • MtnPete says:
    4 of 4 people found the following review helpful
    4.0 out of 5 stars
    They’re good; I like them, September 21, 2016
    By 
    MtnPete (Grand Forks, ND USA) –

    Verified Purchase(What’s this?)
    This review is from: ARB 6821201 Fog Light Kit For Deluxe ARB Bumpers (Automotive)
    To be clear this item contains (2) lights (the bulbs, lens, back housing), two adjusting screws and springs, and very short wires (about 5″). The ones I previously bought directly from ARB lasted 5 years of very light use. They’re good; I like them, but they’re not great. Fog lights can be expensive so I’m happy with the cost/quality. Additionally, the plastic bumper housing requires this specific light. If anyone has a solution for a different light, let me know; I’ll eventually need a new one. So far I know LabRak makes a great $400 upgrade option, but that’s too rich for my blood.

    Help other customers find the most helpful reviews 

    Was this review helpful to you? Yes
    No

  • W. Blaine says:
    2 of 2 people found the following review helpful
    4.0 out of 5 stars
    Almost perfect., September 3, 2013
    By 
    W. Blaine
    (REAL NAME)
      

    Verified Purchase(What’s this?)
    This review is from: ARB 6821201 Fog Light Kit For Deluxe ARB Bumpers (Automotive)
    I have installed this “RU” bar on my 2013 Tacoma Access cab with TRD. I rate it one star off because of a slight fitting problem with the bumper bracket to the frame. It was necessary to file the mounting holes in the bracket 3/16 inch to get it to fit. Took about 15 minutes with a rat tail file. Not a big deal and it didn’t effect the final alignment or appearance. The printed instructions are in B&W. I highly suggest contacting ARBUSA and having them email the pdf of the instruction. Than you will have color pictures with enough resolution to magnify. Now you can see what you’re doing. I’m impressed with the quality of the mounting hardware, as in nuts and bolts. The finish is great! You will have to buy the ARB fog lights as the OEM will not fit. It is also suggested to replace the filament turn signal 1156 bulbs with led type. Fog light kit and bulbs another $90. I had existing fog lamps so wiring was there and the dash switch. The marker lamp/turn signals wired up easily per the instruction. I also installed a Warn M8000 winch. The install is very detailed in the ARB bumper instruction. You will have to drill a couple of 3/8 inch holes in the fairlead to make it fit the winch mounting holes on the bottom. I was able to attach the red positive to an existing post on my battery. The negative lead bolted to the frame, just to the right of the battery negative. I bumper comes with another set of winch cables to connect the control box to the winch. I used the existing cables that came with the winch. The plastic fender liners with need to be tie rapped up to the frame. I re-enforced the hole in the plastic before tying them up and I think it will work just fine. Yes, you will have to cut the top few inches off your existing bumper to use as a trim to the ARB. I removed the OEM fog lamps and the center section of the bumper, before tossing the rest. It’s just a couple pounds of plastic. You will also remove the aluminum crush bar and two frame extentions. The weight of the bumper and winch will be close to 200 pounds. I found that this will cause a front end sag of maybe 2 inches. I have ordered the suggested springs and shocks to replace the OEM springs and Bilsteins. The springs are OME 2886 ($162.00 the pair) and OME Nitrocharger shock/strut N140S ($292.00 the pair). The Bilsteins may actually fit, but performance with the OME springs is questionable. I’m in so deep now, why scrimp on the shocks? I compared prices and bought all of these items on Amazon. While I’ve spent considerably more than intended, I’m very happy with the results. No kangaroos in Montana, but plenty of deer. I’m confident the bumper will withstand anything up to bison. It is one heck of a bumper.
    Help other customers find the most helpful reviews 

    Was this review helpful to you? Yes
    No

  • 173 says:
    3 of 3 people found the following review helpful
    1.0 out of 5 stars
    Not needed., September 8, 2016
    By 
    173

    Verified Purchase(What’s this?)
    This review is from: ARB 6821201 Fog Light Kit For Deluxe ARB Bumpers (Automotive)
    These are JUST the fog lights. Not the insert like I assumed. You DO NOT need to buy this. If you have the most modest of fab skills to can mount ANY 4″ round light into the insert that comes with the bumper. I picked up 2 4″ LED lights from eBay instead of these lights. Save yourself some money and don’t bother with these.
    Help other customers find the most helpful reviews 

    Was this review helpful to you? Yes
    No